Motorola launched the Moto One Hyper, back in December 2019. It has so far received a lot of updates and in the near future, the device is expected to get the Android 11 update.
Today Motorola has finally rolled the Android 11 update to the Motorola One Hyper globally which brings all the Android 11 features and customization. In this guide, we will show you how to install the Android 11 firmware file manually on Motorola One Hyper.
Motorola One Hyper Device Overview
The device has a 6.5-inches Full-HD+ IPS LCD display at a resolution of 1080×2340 pixels. It runs on Android 10 with Android One support and powered by Qualcomm Snapdragon 675 SoC. While the device packs Adreno 612 GPU, 4GB RAM, 128GB of internal storage. The storage is expandable up to 1TB via a MicroSD card.
It sports a dual rear camera setup of a 64MP (f/1.8) wide-angle sensor and an 8MP ultrawide sensor. The rear cameras have PDAF, an LED flash, HDR, Panorama support. While the front features a 32MP (wide, f/2.0) motorized pop-up selfie camera with HDR mode.
The phone is backed by a 4000mAh battery with 45W fast charging support. It has the Wi-Fi 802.11 a/b/g/n/ac, a 3.5mm audio jack, Bluetooth 5.0, GPS, A-GPS, GLONASS, NFC, USB Type-C port, etc. In terms of the sensors, it has a rear-mounted fingerprint sensor, gyroscope, accelerometer, proximity, and a compass sensor.
Download Motorola One Hyper Android 11 Update
Here you can download the official Android 11 for the Motorola One Hyper.
Steps to Install Motorola One Hyper Android 11 Update
Now, if you’re ready to flash the Android 11 manually on your Motorola One Hyper device then you need to download the drivers, firmware file, and tools. So, without wasting any more time, let’s get into it.
Pre-Requirements:
- This ROM is supported for the Motorola One Hyper variant only.
- Make sure that your device should be charged at least 50% or higher.
- You will require a PC or Laptop with a USB Data Cable.
- We always recommend our readers take a full data backup of the device for safety purposes.
- Install Motorola USB Drivers and Rescue and Smart Assistant Tool on your PC
- Download ADB and Fastboot Tool or Android SDK Platform tool
Firmware Installation Guide:
Check out the firmware flashing guide below for the Motorola One Hyper. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.
Disclaimer:
Step 1. Bootloader Mode
Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold the volume down, and turn it on. You should see the bootloader screen.
Step 2. Connect Your Device to PC:
After booting your Motorola One Hyper into bootloader mode, now connect it to the PC using the USB Cable.
Step 3. Download Stock ROM/Firmware:
To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.
You can also download the full stock ROM from the above download flash file section on this guide.
Step 4. Flashing Guide:
- The next step is to open the command window and go to the adb folder
- Enter the following command to flash the firmware.
- fastboot oem fb_mode_set
- fastboot flash partition gpt.bin
- fastboot flash bootloader bootloader.img
- fastboot flash vbmeta vbmeta.img
- fastboot flash bluetooth BTFM.bin
- fastboot flash radio radio.img
- fastboot flash logo logo.bin
- fastboot flash boot boot.img
- fastboot flash dtbo dtbo.img
- fastboot flash dsp dspso.bin
- fastboot flash recovery recovery.img
- fastboot flash super super.img_sparsechunk.0
- fastboot flash super super.img_sparsechunk.1
- fastboot flash super super.img_sparsechunk.2
- fastboot flash super super.img_sparsechunk.3
- fastboot flash super super.img_sparsechunk.4
- fastboot flash super super.img_sparsechunk.5
- fastboot flash super super.img_sparsechunk.6
- fastboot flash super super.img_sparsechunk.7
- fastboot flash erase userdata
- fastboot flash erase ddr
- fastboot oem fb_mode_clear
- Now your device will reboot into bootloader with the firmware you installed.
That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.
fastboot oem fb_mode_set fastboot flash partition gpt.bin fastboot flash bootloader bootloader.img fastboot flash vbmeta vbmeta.img fastboot flash bluetooth BTFM.bin fastboot flash radio radio.img fastboot flash logo logo.bin fastboot flash boot boot.img fastboot flash dtbo dtbo.img fastboot flash dsp dspso.bin fastboot flash recovery recovery.img fastboot flash super super.img_sparsechunk.0 fastboot flash super super.img_sparsechunk.1 fastboot flash super super.img_sparsechunk.2 fastboot flash super super.img_sparsechunk.3 fastboot flash super super.img_sparsechunk.4 fastboot flash super super.img_sparsechunk.5 fastboot flash super super.img_sparsechunk.6 fastboot flash super super.img_sparsechunk.7 fastboot flash erase userdata fastboot flash erase ddr fastboot oem fb_mode_clear
